Choke Tube Installation

Choke Tube Installation

How To: install choke tubes in a shotgun barrel. Demonstration video of how to correctly use reamers and taps to install choke tubes in shotgun. Lots of detailed information, should answer all your questions on the subject.

26 Comments

  1. MultiMrNoone on August 24, 2022 at 8:14 pm

    How often should you break the chip when cutting threads? I have seen when cutting smaller threads it is recommended to back off the tap every half to one turn. Seems like it worked out for you, just curious if the difference in diameters is the cause or what. Awesome video though, just what I was looking for!



  2. Shotgun Reloader on August 24, 2022 at 8:16 pm

    Where is the runout coming from, the 3 jaw chuck or is the reamer bent? it will make the reamed hole larger than desired did you check afterwards to see how much?



  3. christakis100 on August 24, 2022 at 8:17 pm

    Hi there. Is any set available for Beretta shotguns choke tubes?



  4. Sebastian Tufigno on August 24, 2022 at 8:17 pm

    When you Tap the barrel after reaming; is the tread from the top to the end of the reamer; meaning.if I have choke tube with the tread at the top instead of the end and it had the same pitch size tread; will it srew up well in the barrel ?



  5. Paul Morin on August 24, 2022 at 8:17 pm

    The sound is very low.



  6. Michael Nashef on August 24, 2022 at 8:17 pm

    where can you buy this set from?



  7. todoslosantilopesonm on August 24, 2022 at 8:20 pm

    Hello how are you ! I want to buy these items where I can do it?
    thanks and regards



  8. TJ Cornish on August 24, 2022 at 8:21 pm

    One’s you put it on your barrow can you take it out later?



  9. Eric Jones Sr on August 24, 2022 at 8:23 pm

    Always wanted to see how it was done. Thanks



  10. Blake M on August 24, 2022 at 8:25 pm

    minimum thickness? want to do this to my mossberg 20 inch 8 shot 500 standard thickness



  11. bakani baleni on August 24, 2022 at 8:26 pm

    do we real need so many chokes in a gun? a full fixed choke in a hunting gun is enough to do all what other chokes can do as along as your shooting distance is well calculated. also not forgetting the use of the right kind of ammo for your hunt.



  12. Chase Fisher on August 24, 2022 at 8:34 pm

    great tutorial!



  13. Rick James Mofo on August 24, 2022 at 8:37 pm

    What if I thread my 12 gauge fixed improved cyledner barrel for a choke without doing the reaming?
    ?



  14. Aaron Menchinger on August 24, 2022 at 8:38 pm

    What size tap and reamer is that?



  15. joe whiteman on August 24, 2022 at 8:45 pm

    in general how much to have this done to my shotgun?



  16. Kyle on August 24, 2022 at 8:52 pm

    Tried to contact Tru – Choke on several occasion to no avail, any suggestions or are they gone ?



  17. ReamerGuy on August 24, 2022 at 8:55 pm

    It’s important to note that you must either cut the barrel back to eliminate to the fixed chokes, or you must ream them out with a separate reamer. The only exception to this is a cylinder bore barrel (no choke).

    https://4drentals.com/measuring-for-screw-in-chokes-shotgun/



  18. Wolfhound on August 24, 2022 at 8:59 pm

    Love the tune at the end bro!



  19. rez guy 209 on August 24, 2022 at 9:02 pm

    Hi um if I got this can I rechoke cuz I accidentally got the wrong choke and it suppose to fit optima plus but my barrel is benelli mobil



  20. TNRonin on August 24, 2022 at 9:04 pm

    URL saved for a project!!! Thanks



  21. Phil Lowman on August 24, 2022 at 9:07 pm

    Do you have contact? Do you sell or rent these choke reamer / tap sets? I have a closet full of shotguns that I’d use often if I had interchangeable chokes for em.



  22. NoBs on August 24, 2022 at 9:08 pm

    So the barrel is fed by hand into the lathe ?? Not what I would have expected..



  23. Edward Porter on August 24, 2022 at 9:08 pm

    A lathe is great if you have one. I did 3 of mine with a hand drill, its slow but I took my time lots of cutting oil and it worked perfect. Ive done 5 others for buddys and no problems.



  24. Matthew Lacy on August 24, 2022 at 9:09 pm

    What is your rpm on your lathe while reaming?



  25. Keepingitreal98 on August 24, 2022 at 9:10 pm

    How much would you say a gunsmith charges to do this?



  26. Death Pig. on August 24, 2022 at 9:10 pm

    thanks for the upload, good video